10 LED DUAL-FUNCTION BAR GRAPH
Contrast Indicator – Provides “at-aglance” performance data.
Lock – When this option is enabled the sensor becomes tamperproof. Note: The remote AUTOSET and programming are not affected by the Lock option.
MEM 1 through MEM 5 - LED indicates MEM location selected. NOTE: Any changes to the sensor will automatically be saved to current MEM # location.
(Patent No. 5,621,205)
EDR® (Enhanced Dynamic Range) circuit prevents dark state saturation and expands the operating range without reducing amplifier gain.
ACT (Automatic Contrast Tracking) automatically adjusts the sensor for diminishing conditions. Ex. Dirty environment, scratched lenses, thermal drift, or LED light power.
AGS (Automatic Gain Select) is an unique feature that provides automatic digital selection of amplifier gain based upon your sensing requirements.
The AUTOSET adjustment routine only requires the push of one button, one time. Oftentimes, in dynamic operating conditions, all you have to do is push the button for a perfect setting. This is dependent upon at least a 4:1 duty cycle ratio.
(Note: The buttons on the sensor are inactive when in communication mode; if COM/LOCK LED is on or blinking)
The XPC is available in four communications options; RS-485 or RS-232 in either MODBUS ASCII or MODBUS RTU protocol. RS-485 for multi-drop applications where sensors need to be addressed and bussed together, or RS-232 for single-drop applications where the sensor is behind safety interlocks, or in hard-to-reach areas that restrict easy access. RS-485 units can have up to 128 sensors per node, depending on cable length. Baud rate and addresses are user selected and defined when utilizing the EyewareXPC software, or proper commands as defined by the Command Set.
RESPONSE TIME SELECTION
60µs, 125µs, and 450µs available.
AUX IO line can be configured as:
- Remote AUTOSET
Remotely AUTOSET the sensor by applying a momentary contact closure from the Remote AUTOSET input wire to negative as shown in the wiring diagram. The Remote AUTOSET command will duplicate the last manual AUTOSET.
- Remote Input
- Action Alert Output
- Output Mode: On
- Output Mode: Off
Note: Configure AUX IO by using complimentary EyewareXPC software or Full Featured Command Set.
Built-in 8-pin M12 Connector.
Built-in DIN rail “Snap-On” design, through hole, or bracket mount.
EyewareXPC Software - Complimentary
EyewareXPC is a free diagnostic tool to aid the user in setting up, testing, and debugging applications. Write your own custom controls using the available full featured Command Set. Note: EyewareXPC Software works only with modbus ASCII versions of XPC.
RS-485 Multidrop. Distinct, customer defined addresses. Up to 128 sensors on one Network.
Buttons are active on screen...manually adjust the sensor UP or DOWN for precise sensor setup.
The blue and red LED Output Indicators are active on the screen and turn on when the output is activated.
These 10 LEDs are active on the screen and respond up and down to each sensor's received light level.
"Click" or "Touch" an area of the sensor on the screen, other than the red/yellow buttons, and you will advance to the screen below, Screen Two. To return to the multi-sensor screen view, or Screen One, click on the Back button in the lower right corner.
Features and Options:
- Downloadable Recipes
- Half Duplex Communication
RS-485 (multi-drop) or RS-232 (single drop)
MODBUS ASCII or RTU
- Five Onboard Memory Locations
- Button Lockout
- Configurable Response time: 60µs, 125µs, or 450µs
- 8-Pin Male, M12 Connector
- Available in White, Red or Infrared LED
- Patent No.'s 5,621,205 and 6,950,778
- 10-LED Dual-Function Bar Graph
- EyewareXPC Software Includes:
Two 4-Segment Digital Displays (Signal Level & Threshold)
Digital Sensor Scope
Full Featured Command Set
Note: EyewareXPC is free demonstration software. Command Set also available for customer interface software.
- P.A.T. Complant
Process Analytical Technology
- No-Touch Setup
- Quick Digital Changeover
- Capture and Save Setups
- Log Sensor Performance
- Digital Process Validation
- Performance Calibration
- Universal Application Flexibility
- Quality Verification